KINERJA DIAGRAM KONTROL W DAN DIAGRAM KONTROL G

  • Marlon S. N. van Delsen Jurusan Matematika FMIPA Universitas Pattimura
  • Mozart W. Talakua Jurusan Matematika FMIPA Universitas Pattimura
DOI: https://doi.org/10.30598/barekengvol10iss2pp137-147
Keywords: Average Run Length, Diagram Kontrol G, Diagram Kontrol W

Abstract

Pengontrolan terhadap variabilitas proses merupakan salah satu hal yang sangat penting dalam bidang industri. Sehingga, saat ini dikembangkan diagram kontrol yang khusus untuk memonitor variabilitas proses. Diagram kontrol multivariat yang digunakan untuk memonitor variabilitas proses antara lain diagram diagram kontrol W dan diagram kontrol G. Salah satu cara yang dapat digunakan untuk melihat kinerja diagram kontrol adalah dengan menggunakan Average Run Length (ARL). Sehingga pada penelitian ini akan dilihat kinerja dari diagram kontrol W dan diagram kontrol G, kemudian membandingkan kinerja diagram kontrol W dan G dengan menggunakan ARL. Hasil dari ARL menunjukkan bahwa nilai ARL yang diperoleh diagram kontrol G lebih kecil dari diagram kontrol W. Berdasarkan hasil tersebut dapat disimpulkan bahwa kinerja diagram kontrol G lebih baik dibandingkan dengan diagram kontrol W, namun untuk pergeseran varian yang besar diagram kontrol W dapat digunakan sebagai pendamping diagram kontrol G.

Downloads

Download data is not yet available.

References

[1] F. B. Alt dan S. J. N. E, Multivariate quality control In Encyclopedia of Statistical Scinces Kotz, New York: John Wiley & Sons, 1985, pp. 110-122.
[2] T. Anderson, An Introduction to Multivariate Statistical Analysis, New York: John Wiley & Sons, Inc, 1984.
[3] Djauhari, M. A., “Improved Monitoring of Multivariate Process Variability. Journal of Quality Technology,” vol. 37, 2005, pp. 32-39.
[4] Kramer, C.Y. dan Jensen, D.R, “Fundamentals of Multivariate Analysis-Part II: Inference About Two Treatments” Journal of Quality Technology, vol. 1, pp. 189-204, 1969.
[5] Levinson, William A., Holmes, D. S. and Mergen, A. E, Variation Chart for Multivariate Processes Quality Engineering, 2002, pp. 539-545.
[6] Montgomery, D. C, “Introduction to Statistical Quality Control,” 6th Edition penyunt, New York, John Wiley & Sons, Inc, 2009.
[7] Noya Van Delsen, M dan Mashuri, M, “Perbandingan Kinerja Diagram Kontrol G dan Diagram Kontrol Improved |S|,” Surabaya.
[8] Rakhmawati, Dwi Yuli, “Perbandingan Kinerja Diagram Kontrol Multivariat untuk Variabilitas Berdasarkan Matriks Kovariansi dan Matriks Korelasi,” Surabaya, 2011.
[9] Sindelar, M.F, “Multivariate Statistical Process Control For Corellation Matrices,” Tesis Ph.D, 2007.
[10] Wen Lu, C. dan Reynolds, M. R, “ Cususm Charts for Monitoring an Autocorrelated Process,” Journal of Quality Technology, pp. 316-334., 2001.
Published
2016-12-01
How to Cite
[1]
M. van Delsen and M. Talakua, “KINERJA DIAGRAM KONTROL W DAN DIAGRAM KONTROL G”, BAREKENG: J. Math. & App., vol. 10, no. 2, pp. 137-147, Dec. 2016.
Issue
Vol 10 No 2 (2016): BAREKENG: Jurnal Ilmu Matematika dan Terapan
Section
Articles

Authors who publish with this Journal agree to the following terms:

  1. Author retain copyright and grant the journal right of first publication with the work simultaneously licensed under a creative commons attribution license that allow others to share the work within an acknowledgement of the work’s authorship and initial publication of this journal.
  2. Authors are able to enter into separate, additional contractual arrangement for the non-exclusive distribution of the journal’s published version of the work (e.g. acknowledgement of its initial publication in this journal).
  3. Authors are permitted and encouraged to post their work online (e.g. in institutional repositories or on their websites) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published works.

Most read articles by the same author(s)

<< < 1 2 3 > >>